Dynamat installer

Find Dealer. Sound Heat Vibration. Focus Sound Where You Want and Keep It There Dynamat is a thin, flexible, easy to cut and mold sheet that actually stops noise causing resonance and vibration, by using visco-elastic qualities that promote vibro-acoustic energy conversion.

Engine and exhaust heat make your vehicle miserably hot and uncomfortable. Stop the Noise and its Source. Dynamat — a 25 year partner of SEMA is proud to be back in Vegas showcasing our industry leading product line, be sure to come by and check out or booth. There should be a set of screws or bolts underneath that need to be removed. Underneath the handbrake should also be a set of screws usually covered by a clip. Using the trim removal kit, take off the clip and loosen the screws.

Then check the side and back of the armrest compartment for bolts or screws. If you have a cupholder, this should be removed, which may reveal another set of screws. The sides of the front part of the console also may have plastic clips or screws.

Remove all of these as well. This part will need patience as you will need to move the console around until you find the right angle to remove it. Finally, you should be able to unclip the console and remove it entirely from the car. The front seat safety belts are anchored to the floor. There should be another plastic clip covering a bolt.

Remove these. Some of the side trims or kickboards will need to be removed to get to your car flooring. You will need to inspect the panels first.

This needs to be removed. First, check for any exposed screws holding the trim in place and remove these. If you do not find screws check the panel to see where the clips are positioned by moving it around a little to establish the pressure.

At the pressure point, you should find the clip underneath the panel. Then using the panel removal tool, slide the head under the panel and gently push down on the lever to lift it.

Do this around all the door frames Where the carpet is being held in place. Finally, if needed, unplug all the wiring carefully. Using the proper tool here will avoid you breaking the panel pins which you need when replacing everything. You may also find a pedal plate holding the carpet in place, which needs to be removed by loosening the bolts.

Adding Dynamat to the rear deck will improve the sound quality of your car speakers. However, this is not required to remove with a floor installation. If you followed the steps above, you should be ready to remove the carpet.

Do a last check to ensure the carpet is loosened from all clips, screws, and bolts. The best way to remove the carpet is to roll or fold it as you go along.

Start from the front under the steering wheel where the pedals are. Then move to the front passenger side and then up to the gear. These are the trickiest areas to get out. Next, thread through all the wiring carefully. Then continue rolling the carpet up to the back seat. Finally, remove it completely from the back car door. The surface area needs to be cleaned before you apply the Dynamat. First, use a vacuum to remove any loose dirt. Then use a cloth with rubbing alcohol to clean off any oil and grease marks.

Then move onto the seating area and continue towards the back of the car. Finally, remove it from the back door. This gives you an excellent opportunity to Vaccum the carpet while you are at it. Use the Vaccum to get rid of any dirt on the floor and use a cloth with alcohol rubbing to remove any oil and grease. It can alter the effectiveness of the material. If you have already measured and area, then well and good. Otherwise, the floor carpet will help you with that. Cut the Dynamat Xtreme accordingly with the help of a sharp knife, a scissor can also be used, but due to the thickness, the former is more preferable.

For better results, let the Dynamat bask in the sunlight for an hour, so the glue becomes adhesive. Now place the sound dampening material where you want to apply it. Once satisfied, peel the adhesive layer from the top half and stick it to the area and roll it till it holds.

Then remove the bottom part of the layer and apply it the same way. The whole process applies to the other parts like trunk and doors, as well. After this place, the floor mats over the soundproofing material. And finally, screw the seats back in place. For installing the Dynamat on the floor, remember to follow the half peel half stick approach. This makes the whole process more accurate and easier to manage.

Once the sound deadening material is applied you will notice a significant decrease in the noise and the audio experience will be enhanced.

If you are interested in soundproofing your room , then you will like our guide on it. Table of Contents.