Menvier 2500 engineer manual

Set JP4 to the TS position. Finally clip the XNode cover onto the base being careful not to trap any cables or to Secure the base to appropriate terminals see Figure The configure the TS to monitor a XB power control unit tests the battery at pre- supply unit.

It is recommended that cable ties The TS has an overload protection are used to keep cables separated. If the power supply is overloaded, the 3. Reset Activates when a circuit is in a fault Active all the time to power latching condition during exit, deactivates when the detectors smoke detectors, shock sensors fault is reset.

The TS can monitor up to detection Final Exit circuits, each circuit must be programmed in This must be the first detector or door contact order for the system to respond correctly. When using the circuit period is initiated by entering the Engineers for this type of monitoring the circuit MUST have passcode.

Omittable Circuits with this attribute can be omitted by the Security A circuit used to lock-out keypad operation. A to P, each circuit can be assigned into one or Bell dly wards A to P more wards. Deferred As Timed Exit, however, if any circuits are activated during the exit procedure the exit timer is restarted.

Lock Set To use this method you must install a lock switch with the contacts connected to a lockset zone type. Set only When using output modules or outputs that When using a DC58M digi-modem, the are programmed as circuit mimic, the digi-modem will always attempt to answer outputs will only mimic the circuit if the incoming calls.

Three types of chime tones are available: Chime 1 Generates a single two-tone chime sound. Chime 2 Generates a double two-tone chime sound. The [A] and [C] keys allow you to The system disable the remote service option. Each time switch can be 10 part-set groups. Page Use On-Line Pad [] For example you could use this option to connect to another TS alarm system and once on-line you can use your own keypad to set the remote site.

Paste When you have selected the circuit that you LCD on all TS remote keypads. Test Keypads Flowchart Display View Network Errors Flowchart False Setting Routine This option allows the engineer to set the system whilst the premises are occupied.

The output is designed to operate only eight custom outputs type. The diagram below Page Call Back No. This option allows the first call back telephone This option allows the Modem site number to be number to be programmed. COM1 Baud rate This option allows the engineer to set the baud rate for the general communication port For future use.

If the extension loudspeaker is connected to Page 22 If these pins are shorted whilst the system is Two removable memory devices that store the powered, the control panel will re-learn all devices operating software for the TS system. External Sounder Connections It will also function as a standard digicom if required.

The unit Page Pre Power-Up Checks 1. This will ensure the factory default circuit. PC Output 3 On Ward Clear Activates when the selected ward is clear of faults Page Program Circuits Exit Term A circuit that is normally connected to a push button The TS can monitor up to detection circuits, outside the protected area, which can be used to finally each circuit must be programmed in order for the set the area.

Page Circuit Wards Activity Circuits with this attribute are monitored so that when The TS has sixteen wards which are labelled A to P, they activate the circuit activation is stored. When the each circuit can be assigned into one or more wards. When an listed below. Page 52 If this is the case then the only way of returning the system to its factory default setting is by returning the control panel PCB to Menvier Security.

Re-arms apply to Ward A Hi Security ward The circuit status conditions and resistance are format on LCD remote keypads. Chime 1 Generates a single two-tone chime sound. This option allows the engineer to define up to 10 Each time switch can be programmed with up to three part-set groups.

Page Use On-Line Pad If the system is fitted with a DC58M digi-modem, you This option allows the engineer to assign a name 8 can use this option to connect to another TS or characters to each user. Paste When you have selected the circuit that you require to This means that only the outputs allocated to ward A will trigger. This Interface will allow the connection of remote keypads or nodes, up to a maximum distance of 1km from the Driver Board.

It can also be used in situations that require cabling to be run in areas with electrical or radio interference. NetLCD Sounder Control Jumper When the jumper is set to enabled the keypad sounder activates when the panel speaker and the output on the keypad are active at the same time.

Use Engineering Menu 4 option 3 to assign the control panel speaker to all wards that need tones from their keypad sounders. Use Engineering Menu 3 option 8 to assign the outputs of the keypads to ward sounder control for the relevant wards.

Internal Digital Communicator. To use the internal digital communicator you must connect a stand alone digital communicator that is only programmed with the central station phone number. Use Engineering Menu 3 option C 9 to set up accounts to wards and program digi channels. Always remove power mains and battery from the system before adding or removing equipment. Initial Power Up When you initially power up the system will ask you to confirm the equipment attached to the networks.

If the system reports more Lecs than you have actually connected it may be that a remote keypad is not initialised. The control panels sees remote keypads that have not been initialised as Lecs. To initialise a keypad press any of the keys. Keypads If you connect a remote keypad to a Network then you lose six zones.

The control panel sees a keypad that is directly connected to a Network cable as equivalent to an xnode or ts node. All such devices provide zone numbers in blocks of eight.

Since the keypad itself can only provide connections for two zones then the remaining six zone numbers cannot be used.

Keypads connected to separate Networks can be used simultaneously. In the same way, keypads connected to separate xnodes do not lock each other out. You cannot disable channels on the internal communicator. The only way to do this is to assign channels to an event that is not going to cause an alarm.

User Codes Note that if you change any channel output on the internal communicator then you are changing it for every ward. When such a user sets a ward from a keypad that is not allocated to the ward then the control panel will set the ward instantly. One of the most difficult of faults to find is when the control panel looses communication with an item of remote equipment, for example an xnode.

This may be caused by one of the following problems: network equipment faulty, power supply faults, earthing faults, or cabling faults. Use Network Errors to check if you have any data problems. Press 0 to reset the error counter. Power down and disconnect the node indicated in the display 2,07 in the example shown above. Re-attach the network cable so that the rest of the newtwork is still connected to the control panel. Re-apply power. Confirm the new number of network devices connected as described in the TS Installation Manual.

While the black lead is still connected to earth set the meter to low dc. Connect the red lead to A and then to B. If the meter shows a stable reading greater than about 0. Check the entire length of the cable for wiring faults or damage, for example staples through the cable.

Please note that some power supplies have a grounded printed circuit board. If one of these is connected to your network then you will have earthing problems. XB power supplies. If none of the problems above exist then check the continuity of the cable. If all else fails then power down the panel and connect a single xnode to the panel on a short length of cable.

Power up the panel. Confirm that only one device is connected, as described in the TS Installation Manual. Check again for network errors. If the keypad still displays network errors then power down again and connect the xnode to another network. Power up, confirm that only one xnode is connnected and check again for network errors. If the errors have gone then the control panel has got a faulty network. Repeat steps 1 and 2 to check wether there are any data errors.

If there are no errors then the node you have disconnected is faulty 4.